Hey everyone I have a few questions. I’m running TrueNas community edition and I’ve gotten critical alerts. I’m worried about two hdds currently.
/dev/sda [SAT], 1 Currently unreadable (pending) sectors.
/dev/sdd [SAT], 2 Currently unreadable (pending) sectors.
/dev/sda [SAT], 1 Offline uncorrectable sectors.
/dev/sda [SAT], Self-Test Log error count increased from 0 to 1.
These are the errors I get.
My smartctl -x results for sda:
=== START OF INFORMATION SECTION ===
Device Model: MG08ACP16TE
Serial Number: X1V0AAGRFWXG
LU WWN Device Id: 5 000039 b38e30355
Firmware Version: 1506
User Capacity: 16,000,900,661,248 bytes [16.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database 7.3/5894
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Oct 29 13:27:15 2025 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1], Master PW ID: 0xfffd
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 113) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 70) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0
2 Throughput_Performance P-S— 100 100 050 - 0
3 Spin_Up_Time POS–K 100 100 001 - 5536
4 Start_Stop_Count -O–CK 100 100 000 - 30
5 Reallocated_Sector_Ct PO–CK 100 100 010 - 2
7 Seek_Error_Rate PO-R-- 100 100 050 - 0
8 Seek_Time_Performance P-S— 100 100 050 - 0
9 Power_On_Hours -O–CK 043 043 000 - 22808
10 Spin_Retry_Count PO–CK 100 100 030 - 0
12 Power_Cycle_Count -O–CK 100 100 000 - 18
23 Helium_Condition_Lower PO—K 100 100 075 - 65535
24 Helium_Condition_Upper PO—K 100 100 075 - 65535
187 Reported_Uncorrect -O–CK 100 100 000 - 0
188 Command_Timeout -O–CK 100 100 000 - 0
191 G-Sense_Error_Rate -O–CK 100 100 000 - 0
192 Power-Off_Retract_Count -O–CK 100 100 000 - 15
193 Load_Cycle_Count -O–CK 100 100 000 - 30
194 Temperature_Celsius -O—K 100 100 000 - 38 (Min/Max 19/48)
196 Reallocated_Event_Count -O–CK 100 100 000 - 2
197 Current_Pending_Sector -O–CK 100 100 000 - 1
198 Offline_Uncorrectable ----CK 100 100 000 - 1
199 UDMA_CRC_Error_Count -O–CK 200 200 000 - 0
220 Disk_Shift -O---- 100 100 000 - 84148231
222 Loaded_Hours -O–CK 043 043 000 - 22807
223 Load_Retry_Count -O–CK 100 100 000 - 0
224 Load_Friction -O—K 100 100 000 - 0
226 Load-in_Time -OS–K 100 100 000 - 588
240 Head_Flying_Hours P----- 100 100 001 - 0
241 Total_LBAs_Written -O–CK 100 100 000 - 3020987000320
242 Total_LBAs_Read -O–CK 100 100 000 - 3655940033612
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 5 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x0c GPL R/O 513 Pending Defects log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x24 GPL R/O 65520 Current Device Internal Status Data log
0x25 GPL R/O 65520 Saved Device Internal Status Data log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xb8 GPL VS 1 Device vendor specific log
0xbb GPL VS 1 Device vendor specific log
0xc8-0xc9 GPL,SL VS 2 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 206 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It “wraps” after 49.710 days.
Error 206 [5] occurred at disk power-on lifetime: 21384 hours (891 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
04 – 53 00 00 00 00 00 07 fe 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
5f 00 01 00 01 00 00 00 07 fe 00 00 00 36d+08:39:51.947 TRUSTED SEND DMA
e8 00 00 00 01 00 00 00 00 00 00 00 00 36d+08:39:51.947 WRITE BUFFER
e8 00 00 00 01 00 00 00 00 00 00 00 00 36d+08:39:51.947 WRITE BUFFER
5f 00 01 00 01 00 00 00 07 fe 00 00 00 36d+08:39:51.946 TRUSTED SEND DMA
5d 00 01 00 08 00 00 00 07 fe 00 00 00 36d+08:39:51.946 TRUSTED RECEIVE DMA
Error 205 [4] occurred at disk power-on lifetime: 21350 hours (889 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
04 – 53 00 00 00 00 00 07 fe 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+23:26:05.126 TRUSTED SEND DMA
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+23:26:05.126 WRITE BUFFER
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+23:26:05.126 WRITE BUFFER
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+23:26:05.125 TRUSTED SEND DMA
5d 00 01 00 08 00 00 00 07 fe 00 00 00 34d+23:26:04.728 TRUSTED RECEIVE DMA
Error 204 [3] occurred at disk power-on lifetime: 21350 hours (889 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
04 – 53 00 00 00 00 00 07 fe 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+23:26:03.743 TRUSTED SEND DMA
61 00 38 00 c8 00 00 00 13 31 88 40 00 34d+23:26:03.383 WRITE FPDMA QUEUED
60 06 40 00 c0 00 05 4f 37 2f 10 40 00 34d+23:26:03.383 READ FPDMA QUEUED
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+23:26:03.382 WRITE BUFFER
0b 00 00 00 00 00 00 00 00 00 00 a0 00 34d+23:26:03.363 REQUEST SENSE DATA EXT
Error 203 [2] occurred at disk power-on lifetime: 21350 hours (889 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
04 – 53 00 00 00 00 00 07 fe 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+23:26:03.326 TRUSTED SEND DMA
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+23:26:02.842 TRUSTED SEND DMA
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+23:26:02.834 WRITE BUFFER
5d 00 01 00 08 00 00 00 07 fe 00 00 00 34d+23:26:02.493 TRUSTED RECEIVE DMA
0b 00 00 00 00 00 00 00 00 00 00 a0 00 34d+23:26:02.462 REQUEST SENSE DATA EXT
Error 202 [1] occurred at disk power-on lifetime: 21350 hours (889 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
04 – 53 00 00 00 00 00 07 fe 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+23:26:02.439 TRUSTED SEND DMA
61 07 e0 00 48 00 01 6d ae 19 e8 40 00 34d+23:26:01.509 WRITE FPDMA QUEUED
60 04 08 00 40 00 06 92 9b 80 e0 40 00 34d+23:26:01.509 READ FPDMA QUEUED
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+23:26:01.508 WRITE BUFFER
0b 00 00 00 00 00 00 00 00 00 00 a0 00 34d+23:26:01.505 REQUEST SENSE DATA EXT
Error 201 [0] occurred at disk power-on lifetime: 21350 hours (889 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
04 – 53 00 00 00 00 00 07 fe 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+23:26:01.429 TRUSTED SEND DMA
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+23:26:01.419 TRUSTED SEND DMA
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+23:26:01.419 WRITE BUFFER
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+23:26:01.419 WRITE BUFFER
5d 00 01 00 01 00 00 00 00 01 00 00 00 34d+23:26:01.411 TRUSTED RECEIVE DMA
Error 200 [19] occurred at disk power-on lifetime: 21330 hours (888 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
04 – 53 00 00 00 00 00 07 fe 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+03:22:45.122 TRUSTED SEND DMA
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+03:22:45.121 WRITE BUFFER
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+03:22:45.121 WRITE BUFFER
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+03:22:45.108 TRUSTED SEND DMA
5d 00 01 00 08 00 00 00 07 fe 00 00 00 34d+03:22:44.697 TRUSTED RECEIVE DMA
Error 199 [18] occurred at disk power-on lifetime: 21330 hours (888 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
04 – 53 00 00 00 00 00 07 fe 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+03:22:44.215 TRUSTED SEND DMA
5f 00 01 00 01 00 00 00 07 fe 00 00 00 34d+03:22:44.214 TRUSTED SEND DMA
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+03:22:44.214 WRITE BUFFER
e8 00 00 00 01 00 00 00 00 00 00 00 00 34d+03:22:44.214 WRITE BUFFER
5d 00 01 00 08 00 00 00 07 fe 00 00 00 34d+03:22:44.213 TRUSTED RECEIVE DMA
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
1 Extended offline Completed: read failure 10% 22807 31092081184
2 Short offline Completed without error 00% 22461 -
3 Extended offline Completed without error 00% 22105 -
4 Short offline Completed without error 00% 21743 -
5 Extended offline Completed without error 00% 21729 -
6 Vendor (0x70) Completed without error 00% 21477 -
7 Vendor (0x71) Completed without error 00% 21477 -
8 Vendor (0x71) Completed without error 00% 21474 -
9 Short offline Completed without error 00% 21474 -
#10 Vendor (0x70) Completed without error 00% 2 -
#11 Vendor (0x71) Completed without error 00% 2 -
#12 Short offline Completed without error 00% 2 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 1 (0x0001)
Device State: Active (0)
Current Temperature: 38 Celsius
Power Cycle Min/Max Temperature: 32/45 Celsius
Lifetime Min/Max Temperature: 19/48 Celsius
Specified Max Operating Temperature: 55 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
79 01 02 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/55 Celsius
Min/Max Temperature Limit: -40/70 Celsius
Temperature History Size (Index): 478 (468)
Index Estimated Time Temperature Celsius
469 2025-10-29 05:30 37 ******************
… …(221 skipped). … ******************
213 2025-10-29 09:12 37 ******************
214 2025-10-29 09:13 38 *******************
215 2025-10-29 09:14 37 ******************
216 2025-10-29 09:15 38 *******************
… …( 2 skipped). … *******************
219 2025-10-29 09:18 38 *******************
220 2025-10-29 09:19 37 ******************
… …(152 skipped). … ******************
373 2025-10-29 11:52 37 ******************
374 2025-10-29 11:53 38 *******************
375 2025-10-29 11:54 37 ******************
… …( 5 skipped). … ******************
381 2025-10-29 12:00 37 ******************
382 2025-10-29 12:01 38 *******************
383 2025-10-29 12:02 37 ******************
384 2025-10-29 12:03 37 ******************
385 2025-10-29 12:04 37 ******************
386 2025-10-29 12:05 38 *******************
387 2025-10-29 12:06 38 *******************
388 2025-10-29 12:07 38 *******************
389 2025-10-29 12:08 37 ******************
… …( 2 skipped). … ******************
392 2025-10-29 12:11 37 ******************
393 2025-10-29 12:12 38 *******************
394 2025-10-29 12:13 37 ******************
… …( 5 skipped). … ******************
400 2025-10-29 12:19 37 ******************
401 2025-10-29 12:20 38 *******************
402 2025-10-29 12:21 37 ******************
… …( 6 skipped). … ******************
409 2025-10-29 12:28 37 ******************
410 2025-10-29 12:29 38 *******************
… …( 10 skipped). … *******************
421 2025-10-29 12:40 38 *******************
422 2025-10-29 12:41 37 ******************
423 2025-10-29 12:42 38 *******************
… …( 44 skipped). … *******************
468 2025-10-29 13:27 38 *******************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 3) ==
0x01 0x008 4 18 — Lifetime Power-On Resets
0x01 0x010 4 22807 — Power-on Hours
0x01 0x018 6 3020987000320 — Logical Sectors Written
0x01 0x020 6 2291238704 — Number of Write Commands
0x01 0x028 6 3655940033612 — Logical Sectors Read
0x01 0x030 6 2872506535 — Number of Read Commands
0x01 0x038 6 82105200000 — Date and Time TimeStamp
0x02 ===== = = === == Free-Fall Statistics (rev 1) ==
0x02 0x010 4 0 — Overlimit Shock Events
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 139 — Spindle Motor Power-on Hours
0x03 0x010 4 139 — Head Flying Hours
0x03 0x018 4 30 — Head Load Events
0x03 0x020 4 16 — Number of Reallocated Logical Sectors
0x03 0x028 4 211526 — Read Recovery Attempts
0x03 0x030 4 0 — Number of Mechanical Start Failures
0x03 0x038 4 8 — Number of Realloc. Candidate Logical Sectors
0x03 0x040 4 15 — Number of High Priority Unload Events
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 — Number of Reported Uncorrectable Errors
0x04 0x010 4 0 — Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 38 — Current Temperature
0x05 0x010 1 38 N-- Average Short Term Temperature
0x05 0x018 1 37 N-- Average Long Term Temperature
0x05 0x020 1 48 — Highest Temperature
0x05 0x028 1 19 — Lowest Temperature
0x05 0x030 1 47 N-- Highest Average Short Term Temperature
0x05 0x038 1 25 N-- Lowest Average Short Term Temperature
0x05 0x040 1 43 N-- Highest Average Long Term Temperature
0x05 0x048 1 37 N-- Lowest Average Long Term Temperature
0x05 0x050 4 0 — Time in Over-Temperature
0x05 0x058 1 55 — Specified Maximum Operating Temperature
0x05 0x060 4 0 — Time in Under-Temperature
0x05 0x068 1 5 — Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 45 — Number of Hardware Resets
0x06 0x010 4 43 — Number of ASR Events
0x06 0x018 4 0 — Number of Interface CRC Errors
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c)
Index LBA Hours
0 31092081184 22804
1 31092081185 22804
2 31092081186 22804
3 31092081187 22804
4 31092081188 22804
5 31092081189 22804
6 31092081190 22804
7 31092081191 22804
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 5 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 5 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
smartctl -x results for sdd:
=== START OF INFORMATION SECTION ===
Device Model: MG08ACP16TE
Serial Number: 21K0A362FWXG
LU WWN Device Id: 5 000039 ab8d397f0
Firmware Version: 1506
User Capacity: 16,000,900,661,248 bytes [16.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database 7.3/5894
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Oct 29 13:40:08 2025 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1], Master PW ID: 0xfffd
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 241) Self-test routine in progress…
10% of test remaining.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 70) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0
2 Throughput_Performance P-S— 100 100 050 - 0
3 Spin_Up_Time POS–K 100 100 001 - 5710
4 Start_Stop_Count -O–CK 100 100 000 - 55
5 Reallocated_Sector_Ct PO–CK 100 100 010 - 12
7 Seek_Error_Rate PO-R-- 100 100 050 - 0
8 Seek_Time_Performance P-S— 100 100 050 - 0
9 Power_On_Hours -O–CK 029 029 000 - 28474
10 Spin_Retry_Count PO–CK 100 100 030 - 0
12 Power_Cycle_Count -O–CK 100 100 000 - 19
23 Helium_Condition_Lower PO—K 100 100 075 - 65535
24 Helium_Condition_Upper PO—K 100 100 075 - 65535
187 Reported_Uncorrect -O–CK 076 076 000 - 24
188 Command_Timeout -O–CK 100 094 000 - 38
191 G-Sense_Error_Rate -O–CK 100 100 000 - 2
192 Power-Off_Retract_Count -O–CK 100 100 000 - 14
193 Load_Cycle_Count -O–CK 100 100 000 - 56
194 Temperature_Celsius -O—K 100 100 000 - 38 (Min/Max 19/56)
196 Reallocated_Event_Count -O–CK 100 100 000 - 12
197 Current_Pending_Sector -O–CK 100 100 000 - 2
198 Offline_Uncorrectable ----CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -O–CK 200 200 000 - 0
220 Disk_Shift -O---- 100 100 000 - 252968971
222 Loaded_Hours -O–CK 029 029 000 - 28471
223 Load_Retry_Count -O–CK 100 100 000 - 0
224 Load_Friction -O—K 100 100 000 - 0
226 Load-in_Time -OS–K 100 100 000 - 594
240 Head_Flying_Hours P----- 100 100 001 - 0
241 Total_LBAs_Written -O–CK 100 100 000 - 3439085004968
242 Total_LBAs_Read -O–CK 100 100 000 - 3606289339592
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 5 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x0c GPL R/O 513 Pending Defects log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x24 GPL R/O 65520 Current Device Internal Status Data log
0x25 GPL R/O 65520 Saved Device Internal Status Data log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xb8 GPL VS 1 Device vendor specific log
0xbb GPL VS 1 Device vendor specific log
0xc8-0xc9 GPL,SL VS 2 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 491 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It “wraps” after 49.710 days.
Error 491 [10] occurred at disk power-on lifetime: 27147 hours (1131 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
40 – 53 00 28 00 00 92 9c b2 98 e0 00 Error: UNC 40 sectors at LBA = 0x929cb298 = 2459742872
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
25 00 00 08 08 00 00 92 9c aa b0 e0 00 18d+09:07:35.038 READ DMA EXT
25 00 00 08 08 00 00 43 9f ac 60 e0 00 18d+09:07:35.026 READ DMA EXT
25 00 00 08 08 00 00 92 44 3a 98 e0 00 18d+09:07:35.015 READ DMA EXT
25 00 00 08 08 00 00 92 73 69 98 e0 00 18d+09:07:35.004 READ DMA EXT
25 00 00 08 08 00 00 90 ab db d0 e0 00 18d+09:07:34.993 READ DMA EXT
Error 490 [9] occurred at disk power-on lifetime: 27145 hours (1131 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
40 – 53 05 80 00 00 05 ce 73 18 e0 00 Error: UNC 1408 sectors at LBA = 0x05ce7318 = 97415960
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
25 00 00 08 00 00 00 05 ce 70 98 e0 00 18d+07:06:22.539 READ DMA EXT
25 00 00 08 00 00 02 5c 1d 7b 90 e0 00 18d+07:06:22.534 READ DMA EXT
25 00 00 08 00 00 02 5c 1d 73 90 e0 00 18d+07:06:22.530 READ DMA EXT
25 00 00 08 00 00 02 5c 1d 6b 90 e0 00 18d+07:06:22.526 READ DMA EXT
25 00 00 08 00 00 02 5c 1d 63 90 e0 00 18d+07:06:22.508 READ DMA EXT
Error 489 [8] occurred at disk power-on lifetime: 27143 hours (1130 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
40 – 53 03 b0 00 00 67 5c 29 60 e0 00 Error: UNC 944 sectors at LBA = 0x675c2960 = 1734093152
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
25 00 00 08 00 00 00 67 5c 25 10 e0 00 18d+05:02:35.139 READ DMA EXT
25 00 00 08 00 00 00 67 5c 1d 10 e0 00 18d+05:02:31.185 READ DMA EXT
25 00 00 08 00 00 00 67 5c 15 10 e0 00 18d+05:02:23.781 READ DMA EXT
25 00 00 08 00 00 02 ce 76 4a 78 e0 00 18d+05:02:23.777 READ DMA EXT
25 00 00 08 00 00 02 ce 76 42 78 e0 00 18d+05:02:23.773 READ DMA EXT
Error 488 [7] occurred at disk power-on lifetime: 27142 hours (1130 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
40 – 53 00 18 00 00 03 d0 f5 20 e0 00 Error: UNC 24 sectors at LBA = 0x03d0f520 = 64025888
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
25 00 00 08 08 00 00 03 d0 ed 30 e0 00 18d+04:10:44.806 READ DMA EXT
c8 00 00 00 18 00 00 00 39 c3 88 e6 00 18d+04:10:44.805 READ DMA
25 00 00 08 00 00 00 06 39 bb 88 e0 00 18d+04:10:44.801 READ DMA EXT
25 00 00 08 00 00 00 06 39 b3 88 e0 00 18d+04:10:44.797 READ DMA EXT
25 00 00 08 00 00 00 06 39 ab 88 e0 00 18d+04:10:44.788 READ DMA EXT
Error 487 [6] occurred at disk power-on lifetime: 27023 hours (1125 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
40 – 53 05 40 00 00 05 ca df d8 e0 00 Error: UNC 1344 sectors at LBA = 0x05cadfd8 = 97181656
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
25 00 00 08 00 00 00 05 ca dd 10 e0 00 13d+05:46:33.339 READ DMA EXT
35 00 00 00 08 00 00 33 3c 51 58 e0 00 13d+05:46:33.338 WRITE DMA EXT
25 00 00 07 f8 00 00 27 46 57 f8 e0 00 13d+05:46:33.302 READ DMA EXT
35 00 00 08 10 00 02 66 4c c8 d8 e0 00 13d+05:46:33.297 WRITE DMA EXT
35 00 00 08 00 00 02 66 4c c0 d8 e0 00 13d+05:46:33.293 WRITE DMA EXT
Error 486 [5] occurred at disk power-on lifetime: 26991 hours (1124 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
40 – 53 01 70 00 00 52 31 b6 50 e0 00 Error: UNC 368 sectors at LBA = 0x5231b650 = 1378989648
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
25 00 00 08 00 00 00 52 31 af b8 e0 00 11d+21:49:52.697 READ DMA EXT
25 00 00 08 00 00 00 52 31 a7 b8 e0 00 11d+21:49:52.418 READ DMA EXT
35 00 00 00 08 00 01 25 a6 31 c0 e0 00 11d+21:49:52.418 WRITE DMA EXT
25 00 00 01 90 00 01 18 8e ad b8 e0 00 11d+21:49:52.411 READ DMA EXT
25 00 00 08 00 00 00 52 31 9f b8 e0 00 11d+21:49:51.973 READ DMA EXT
Error 485 [4] occurred at disk power-on lifetime: 26978 hours (1124 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
40 – 53 04 58 00 00 4a 3a 4c 18 e0 00 Error: UNC 1112 sectors at LBA = 0x4a3a4c18 = 1245334552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
25 00 00 08 08 00 00 4a 3a 48 68 e0 00 11d+08:31:30.049 READ DMA EXT
25 00 00 00 18 00 02 eb d3 01 e8 e0 00 11d+08:31:30.048 READ DMA EXT
25 00 00 08 10 00 02 da 2f 3f d8 e0 00 11d+08:31:30.036 READ DMA EXT
25 00 00 08 00 00 02 eb d2 f9 e8 e0 00 11d+08:31:30.032 READ DMA EXT
25 00 00 08 00 00 02 eb d2 f1 e8 e0 00 11d+08:31:30.027 READ DMA EXT
Error 484 [3] occurred at disk power-on lifetime: 26965 hours (1123 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER – ST COUNT LBA_48 LH LM LL DV DC
– – – == – == == == – – – – –
40 – 53 07 48 00 00 02 d5 8b 88 e0 00 Error: UNC 1864 sectors at LBA = 0x02d58b88 = 47549320
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
– == – == – == == == – – – – – --------------- --------------------
25 00 00 08 08 00 00 02 d5 8a c8 e0 00 10d+19:48:04.896 READ DMA EXT
25 00 00 08 08 00 02 0e 99 dd 38 e0 00 10d+19:48:04.805 READ DMA EXT
25 00 00 07 30 00 00 3e 5c b8 10 e0 00 10d+19:48:04.750 READ DMA EXT
25 00 00 08 08 00 03 bc 82 09 28 e0 00 10d+19:48:04.743 READ DMA EXT
25 00 00 01 b0 00 02 4f 6e f1 d0 e0 00 10d+19:48:04.713 READ DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
1 Short offline Completed without error 00% 28127 -
2 Extended offline Completed without error 00% 27786 -
3 Short offline Completed without error 00% 27409 -
4 Extended offline Completed without error 00% 27395 -
5 Vendor (0x70) Completed without error 00% 27192 -
6 Vendor (0xb1) Interrupted (host reset) 90% 27192 -
7 Vendor (0x71) Aborted by host 10% 27192 -
8 Vendor (0x70) Completed without error 00% 27189 -
9 Vendor (0xb1) Interrupted (host reset) 90% 27189 -
#10 Vendor (0x71) Aborted by host 10% 27189 -
#11 Short offline Completed without error 00% 27188 -
#12 Vendor (0x70) Completed without error 00% 3 -
#13 Vendor (0x71) Completed without error 00% 3 -
#14 Short offline Completed without error 00% 3 -
#15 Vendor (0x70) Completed without error 00% 0 -
#16 Vendor (0x71) Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 1 (0x0001)
Device State: DST executing in background (3)
Current Temperature: 38 Celsius
Power Cycle Min/Max Temperature: 32/46 Celsius
Lifetime Min/Max Temperature: 19/56 Celsius
Specified Max Operating Temperature: 55 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
7b 01 02 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/55 Celsius
Min/Max Temperature Limit: -40/70 Celsius
Temperature History Size (Index): 478 (147)
Index Estimated Time Temperature Celsius
148 2025-10-29 05:43 37 ******************
149 2025-10-29 05:44 37 ******************
150 2025-10-29 05:45 38 *******************
… …( 7 skipped). … *******************
158 2025-10-29 05:53 38 *******************
159 2025-10-29 05:54 37 ******************
160 2025-10-29 05:55 37 ******************
161 2025-10-29 05:56 38 *******************
162 2025-10-29 05:57 37 ******************
… …( 5 skipped). … ******************
168 2025-10-29 06:03 37 ******************
169 2025-10-29 06:04 38 *******************
170 2025-10-29 06:05 37 ******************
171 2025-10-29 06:06 38 *******************
… …( 2 skipped). … *******************
174 2025-10-29 06:09 38 *******************
175 2025-10-29 06:10 37 ******************
176 2025-10-29 06:11 37 ******************
177 2025-10-29 06:12 37 ******************
178 2025-10-29 06:13 38 *******************
179 2025-10-29 06:14 38 *******************
180 2025-10-29 06:15 37 ******************
… …(170 skipped). … ******************
351 2025-10-29 09:06 37 ******************
352 2025-10-29 09:07 38 *******************
353 2025-10-29 09:08 38 *******************
354 2025-10-29 09:09 38 *******************
355 2025-10-29 09:10 37 ******************
356 2025-10-29 09:11 38 *******************
… …( 6 skipped). … *******************
363 2025-10-29 09:18 38 *******************
364 2025-10-29 09:19 37 ******************
365 2025-10-29 09:20 37 ******************
366 2025-10-29 09:21 38 *******************
367 2025-10-29 09:22 38 *******************
368 2025-10-29 09:23 37 ******************
369 2025-10-29 09:24 37 ******************
370 2025-10-29 09:25 38 *******************
371 2025-10-29 09:26 37 ******************
… …( 17 skipped). … ******************
389 2025-10-29 09:44 37 ******************
390 2025-10-29 09:45 38 *******************
391 2025-10-29 09:46 37 ******************
392 2025-10-29 09:47 37 ******************
393 2025-10-29 09:48 38 *******************
394 2025-10-29 09:49 37 ******************
395 2025-10-29 09:50 38 *******************
… …( 17 skipped). … *******************
413 2025-10-29 10:08 38 *******************
414 2025-10-29 10:09 37 ******************
415 2025-10-29 10:10 38 *******************
… …( 31 skipped). … *******************
447 2025-10-29 10:42 38 *******************
448 2025-10-29 10:43 37 ******************
449 2025-10-29 10:44 38 *******************
… …( 36 skipped). … *******************
8 2025-10-29 11:21 38 *******************
9 2025-10-29 11:22 37 ******************
10 2025-10-29 11:23 38 *******************
… …(136 skipped). … *******************
147 2025-10-29 13:40 38 *******************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 3) ==
0x01 0x008 4 19 — Lifetime Power-On Resets
0x01 0x010 4 28472 — Power-on Hours
0x01 0x018 6 3439085004968 — Logical Sectors Written
0x01 0x020 6 2425027307 — Number of Write Commands
0x01 0x028 6 3606289339592 — Logical Sectors Read
0x01 0x030 6 2628678411 — Number of Read Commands
0x01 0x038 6 102499200000 — Date and Time TimeStamp
0x02 ===== = = === == Free-Fall Statistics (rev 1) ==
0x02 0x010 4 2 — Overlimit Shock Events
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 1031 — Spindle Motor Power-on Hours
0x03 0x010 4 1031 — Head Flying Hours
0x03 0x018 4 56 — Head Load Events
0x03 0x020 4 96 — Number of Reallocated Logical Sectors
0x03 0x028 4 539507 — Read Recovery Attempts
0x03 0x030 4 0 — Number of Mechanical Start Failures
0x03 0x038 4 16 — Number of Realloc. Candidate Logical Sectors
0x03 0x040 4 14 — Number of High Priority Unload Events
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 24 — Number of Reported Uncorrectable Errors
0x04 0x010 4 38 — Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 38 — Current Temperature
0x05 0x010 1 38 N-- Average Short Term Temperature
0x05 0x018 1 37 N-- Average Long Term Temperature
0x05 0x020 1 56 — Highest Temperature
0x05 0x028 1 19 — Lowest Temperature
0x05 0x030 1 55 N-- Highest Average Short Term Temperature
0x05 0x038 1 34 N-- Lowest Average Short Term Temperature
0x05 0x040 1 52 N-- Highest Average Long Term Temperature
0x05 0x048 1 37 N-- Lowest Average Long Term Temperature
0x05 0x050 4 422 — Time in Over-Temperature
0x05 0x058 1 55 — Specified Maximum Operating Temperature
0x05 0x060 4 0 — Time in Under-Temperature
0x05 0x068 1 5 — Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 121 — Number of Hardware Resets
0x06 0x010 4 96 — Number of ASR Events
0x06 0x018 4 0 — Number of Interface CRC Errors
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c)
Index LBA Hours
0 2863317424 28420
1 2863317425 28420
2 2863317426 28420
3 2863317427 28420
4 2863317428 28420
5 2863317429 28420
6 2863317430 28420
7 2863317431 28420
8 2863713064 28420
9 2863713065 28420
10 2863713066 28420
11 2863713067 28420
12 2863713068 28420
13 2863713069 28420
14 2863713070 28420
15 2863713071 28420
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 5 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 5 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
I don’t know how to even read these logs to see what they even mean or if I should be worried.
The smart test results from the gui for sda have “extended offline” as failed 10% remaining.
The smart test results from the gui for sdd have “Vendor (0xb1)”
as ABORTED 90% remaining, “Vendor (0x71)” ABORTED 10% remaining,
Vendor (0xb1) ABORTED 10% remaining, and Vendor (0x71)
ABORTED 10% remaining.
These drives have had 5 bad sectors and running fine but I’m not sure if the sectors increased or not since then.
What should I do? Thanks!