Hi, I woke up to the following error message yesterday.
CRITICAL
Pool volume1 state is ONLINE: One or more devices has experienced an unrecoverable error. An attempt was made to correct the error. Applications are unaffected.
Ran a long smart test which I think is completed by now… Any help on what I’m seeing?
Thanks
root@freenas:~ # smartctl -a /dev/da0
smartctl 7.2 2021-09-14 r5236 [FreeBSD 13.1-RELEASE-p9 amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Ultrastar He10/12
Device Model: WDC WD100EMAZ-00WJTA0
Serial Number: xxxxxxxx
LU WWN Device Id: 5 000cca 273e05f2b
Firmware Version: 83.H0A83
User Capacity: 10,000,831,348,736 bytes [10.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Oct 6 07:04:29 2024 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 93) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: (1164) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0004 129 129 054 Old_age Offline - 112
3 Spin_Up_Time 0x0007 155 155 024 Pre-fail Always - 409 (Average 437)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 108
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000a 100 100 067 Old_age Always - 0
8 Seek_Time_Performance 0x0004 128 128 020 Old_age Offline - 18
9 Power_On_Hours 0x0012 093 093 000 Old_age Always - 51242
10 Spin_Retry_Count 0x0012 100 100 060 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 108
22 Helium_Level 0x0023 100 100 025 Pre-fail Always - 100
192 Power-Off_Retract_Count 0x0032 098 098 000 Old_age Always - 2456
193 Load_Cycle_Count 0x0012 098 098 000 Old_age Always - 2456
194 Temperature_Celsius 0x0002 191 191 000 Old_age Always - 34 (Min/Max 18/41)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 51209 hours (2133 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 80 02 e9 40 00 29d+01:53:25.548 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 29d+01:53:25.548 READ LOG EXT
61 08 38 90 29 ce 40 00 29d+01:53:22.488 WRITE FPDMA QUEUED
61 10 38 78 29 2d 40 00 29d+01:53:22.488 WRITE FPDMA QUEUED
61 08 38 48 62 60 40 00 29d+01:53:22.487 WRITE FPDMA QUEUED
Error 1 occurred at disk power-on lifetime: 51209 hours (2133 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 80 00 e9 40 00 29d+01:53:18.393 READ FPDMA QUEUED
60 e0 08 c8 05 e9 40 00 29d+01:53:18.365 READ FPDMA QUEUED
60 40 38 80 05 e9 40 00 29d+01:53:11.313 READ FPDMA QUEUED
60 00 30 80 04 e9 40 00 29d+01:53:11.313 READ FPDMA QUEUED
60 00 28 80 03 e9 40 00 29d+01:53:11.313 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 51242 -
# 2 Extended offline Completed without error 00% 51236 -
# 3 Short offline Completed without error 00% 51215 -
# 4 Short offline Completed without error 00% 50999 -
# 5 Extended offline Completed without error 00% 50922 -
# 6 Short offline Completed without error 00% 50831 -
# 7 Short offline Completed without error 00% 50663 -
# 8 Extended offline Completed without error 00% 50586 -
# 9 Short offline Completed without error 00% 50495 -
#10 Short offline Completed without error 00% 50255 -
#11 Extended offline Completed without error 00% 50178 -
#12 Short offline Completed without error 00% 50087 -
#13 Short offline Completed without error 00% 49919 -
#14 Extended offline Completed without error 00% 49842 -
#15 Short offline Completed without error 00% 49751 -
#16 Short offline Completed without error 00% 49511 -
#17 Extended offline Completed without error 00% 49434 -
#18 Short offline Completed without error 00% 49343 -
#19 Short offline Completed without error 00% 49180 -
#20 Extended offline Completed without error 00% 49103 -
#21 Short offline Completed without error 00% 49012 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.